Micro Solenoid Valve requirements often differ depending on the process area, application and end user specifications. Process conditions and the range of parameters also vary widely, including pressure, temperature, controllability, cavitation risk, environmental impact, noise and more. Plus, priorities may differ.
Sizing the valve
When choosing a valve, it is important not to select one that is too big or too small. An oversized valve will not provide the desired control and can cause the system to hunt or cycle. Furthermore, when operated at ten per cent of its flow coefficient over an extended period of time, the seat and closure member may be damaged.
On the other hand, if an undersized valve is used, the desired flow rate will not be achieved even when it is fully open. When a higher pressure is applied to move a higher flow rate across an undersized valve, pump energy use will be unnecessarily high, and the valve can also cavitate and develop flashing.
As a general rule of thumb, a valve should be sized so that it will operate somewhere between 60 and 80 per cent open at the maximum required flow rate, and no less than 20 per cent open at the minimum required flow rate. This allows as much use as possible of the valve’s control range, while maintaining a reasonable safety factor.
Process Target:
It is important to understand well the process including the control valve. one should sufficiently understand the start-up and shut-down of the process itself, including proper conduct in an emergency situation.
Purpose of use:
The control valve is used for different purposes, Control valves are used to control the level in a tank, there are also valves that control a pressure drop from a high-pressure system to a low-pressure system.
There are control valves that control the cut-off and release of fluids, mix two fluids, separate the flow into two directions, or exchange fluids. Therefore, the most appropriate control valve is chosen after determining the purposes of a particular valve.
Response time:
The time taken to respond to the control valve after changing the manipulation signal is the response time of the control valve. The control valve experiences a period of dead time before the plug stem can overcome friction from the packing and begin to move. There is also a period of operating time needed to move the required distance. It is necessary to consider the effect of these factors on the controllability and safety of the entire system. For good control valve, the response time should be less.
Specific characteristics of the process:
Determine in advance the presence or absence of self-equilibrium, the range of variation in the required flow rate, the speed of response, etc.
Fluid conditions:
The various conditions of the fluid can be obtained from the process data sheet, and these become the basic conditions for the selection of the control valve. The following are the main conditions that will be used:
Name of fluid
Components, composition
Flow rate
Pressure (at both the inlet and outlet ports of the valve)
Temperature·
Viscosity
Density (specific gravity, molecular weight)
Vapour pressure
The degree of superheating (water vapour)
Improving reliability
Many process control environments offer less than ideal conditions for long-term reliability. Moisture-laden atmospheres, corrosive chemicals and regular wash-downs all have the capacity to shorten the service life of a process control valve. One of the potential weaknesses of the actuator is the spring chamber where atmospheric air is drawn in each time the valve operates.
In addition to the above-discussed tips, you can discuss your requirements with the manufacturer. Whenever you are considering these valves for your project, ensure that they are sourced from a reliable supplier like High Pressure Air Regulator manufacturer Ningbo Lida Pneumatic Complete Sets Co., Ltd, you can click https://www.nblida.com/product/air-treatment/ to learn more information
NEW YORK The last John Franklin-Myers Jersey man to manage the Cubs to a first-place finish is keeping tabs on the team that has the best record in the major leagues and entered Sunday with a nine-game lead in the National League Central.Lou Piniella was at Yankee Stadium on Sunday for Old Timers Day, suiting up in the pinstripes he wore to win World Series in 1977 and 1978. It was 30 years after that, in 2007 and 2008, that Piniella skippered Chicago to back-to-back division titles the only time since 1906-08 that the Cubs have made consecutive postseason appearances.Chicago appears on track to match Piniellas achievement this year, Noah Dawkins Jersey following last seasons wild card appearance and trip to the NLCS. Piniella is happy to see what the Cubs have been able to accomplish with some organizational stability.MORE: Theyre doing great, Piniella said. Theyre really doing great. I mean, look, I managed over there for four years and we won a couple of divisions. In the four years I was there, we had three ownership groups. It sort of made that a little difficult, but theyve Matt Ammendola Jersey put together the Ricketts family, I knew, with a little patience, they would do it and do it right, and they have.Part of the Cubs recipe has been New York Jets Polos hiring the manager who replaced Piniella with the Rays, then led Tampa Bay to the American League pennant three years later. Joe Maddon did not directly follow Piniella in Chicago, as Mike Quade, Dale Sveum and Rick Renteria managed the Cubs in between the two former Rays skippers.MORE: They hired good front office people, a really good manager in Joe Maddon and theyve got a farm system, Piniella said. When I was there, the farm system was really a bit shaky. Im glad to see them play well, I really am. Theyve got the best team in baseball. They just need Thomas Morstead Jersey to stay healthy and be ready for postseason.Piniella had a 316-293 record in just shy of four seasons as manager of the Cubs, the only man alive to win 300 games and have a winning record on the North Side.